Remove the facility wire from the PS2. take away the audio and video cables from the PS2. take awaythe controller from the PS2. Ps2 ribbon cable
Put the bathtub towel on a table. place the PS2 face down on the bathtub towel with the controller ports facing you Ps2 ribbon cable.
Put the tip of the utility knife to a lower place one in all the four rubber feet on rock bottom of the PS2. Wiggle the tip of the utility knife to loosen the rubber foot. Pull the rubber foot off together with yourfingers.
Repeat this procedure with the opposite 3 rubber feet on rock bottom of the PS2.
Repeat this procedure with the 2 plastic nubs on rock bottom of the PS2 that area unit within themiddle.
Remove the screws from to a lower place the rubber feet with the Phillips screwdriver. take away the screws from to a lower place the plastic nubs with the Phillips screwdriver.
Remove the screws from round the controller ports with the Phillips screwdriver.
Rotate the PS2 in order that the facility wire port is facing you. go across the black tape on the right-bottom fringe of the PS2 with the utility knife if it's not already been cut.
Turn the PS2 over on the bathtub towel in order that the “PS2” emblem is facing you. Rotate the PS2clockwise that the long finish is currently facing you.
Grab hold of the left and right sides of the PS2 together with your hands. Pull the PS2 outer case off the PS2 together with your hands.
Rotate the PS2 that the controller ports face you.
Remove the screw from the PS2’s controller port board on the lower left edge mistreatment the Phillips jeweler’s screwdriver.
Remove the screw from the controller port board on the lower right near an identical manner.
Lift the left aspect of the controller port board off the PS2 with the fingers of your hand.
Grab the power/eject ribbon cable that's currently discovered connected to rock bottom of the gamepadcontroller port board mistreatment the fingers of your paw.
Insert the ribbon cable instrumentality at the top of the power/eject ribbon cable into the ribbon cable slot on the PS2’s motherboard that's currently discovered by having upraised the controller portboard up.
Push down on the ribbon cable instrumentality in order that it's firmly seated within the ribbon cable slot.
Place the controller port board back onto the PS2. attach the 2 screws.
Put the PS2’s outer case back onto the PS2. flip the PS2 over. attach the screws. attach the facility wire, the audio and video cables and therefore the gamepad controller. Ps2 ribbon cable
Here's a way to fix the cable/cord from the power/eject button, if you mistakenly pull it out after youopen your PS2. hope it helps
Put the bathtub towel on a table. place the PS2 face down on the bathtub towel with the controller ports facing you Ps2 ribbon cable.
Put the tip of the utility knife to a lower place one in all the four rubber feet on rock bottom of the PS2. Wiggle the tip of the utility knife to loosen the rubber foot. Pull the rubber foot off together with yourfingers.
Repeat this procedure with the opposite 3 rubber feet on rock bottom of the PS2.
Repeat this procedure with the 2 plastic nubs on rock bottom of the PS2 that area unit within themiddle.
Remove the screws from to a lower place the rubber feet with the Phillips screwdriver. take away the screws from to a lower place the plastic nubs with the Phillips screwdriver.
Remove the screws from round the controller ports with the Phillips screwdriver.
Rotate the PS2 in order that the facility wire port is facing you. go across the black tape on the right-bottom fringe of the PS2 with the utility knife if it's not already been cut.
Turn the PS2 over on the bathtub towel in order that the “PS2” emblem is facing you. Rotate the PS2clockwise that the long finish is currently facing you.
Grab hold of the left and right sides of the PS2 together with your hands. Pull the PS2 outer case off the PS2 together with your hands.
Rotate the PS2 that the controller ports face you.
Remove the screw from the PS2’s controller port board on the lower left edge mistreatment the Phillips jeweler’s screwdriver.
Remove the screw from the controller port board on the lower right near an identical manner.
Lift the left aspect of the controller port board off the PS2 with the fingers of your hand.
Grab the power/eject ribbon cable that's currently discovered connected to rock bottom of the gamepadcontroller port board mistreatment the fingers of your paw.
Insert the ribbon cable instrumentality at the top of the power/eject ribbon cable into the ribbon cable slot on the PS2’s motherboard that's currently discovered by having upraised the controller portboard up.
Push down on the ribbon cable instrumentality in order that it's firmly seated within the ribbon cable slot.
Place the controller port board back onto the PS2. attach the 2 screws.
Put the PS2’s outer case back onto the PS2. flip the PS2 over. attach the screws. attach the facility wire, the audio and video cables and therefore the gamepad controller. Ps2 ribbon cable
Video 1
Video 2
farnell,radiospares,
